高壓磁翻板液位計可用于各種塔、罐、罐、球罐、鍋爐的介質液位檢測。高壓磁翻板液位計可實現高密封、防漏，適用于高溫、高壓、耐腐蝕的場合。玻璃液位計測量范圍寬，顯示范圍寬，測量范圍寬。
與其他類型的液位儀表相比，高壓磁翻板液位計的安全性更具優勢，因為它是液位的就地顯示，無需依賴其他電子設備即可實現，穩定可靠，波動小。目前已廣泛應用于火力發電廠的壓力容器中：高低壓除氧器、原水加熱器、熱網加熱器、加熱器、凝汽器等單元換熱器的高、低壓均設有液位計。
換熱器工作介質為易汽化液體，壓力從真空狀態到2.5MPa，溫度從40℃到390℃。因此，液位計日常維護和指示的準確性對壓力容器的安全運行起著至關重要的作用。
本文整理了高壓磁翻板液位計的相關知識，讓我們一起來看看，希望能對您有所幫助！
1、不銹鋼磁性物位計的工作原理
高壓磁翻板液位計（又稱磁浮子液位計）根據浮力和磁耦合原理工作。當被測容器中的液位上升或下降時，液位計主管中的浮子也會上升或下降。浮子中的永磁鋼通過磁力聯軸器傳遞到磁場指示器上，當液位上升時，驅動紅、白柱旋轉180°，當液位下降時，轉向柱由白色變為紅色，指示器的紅白邊界是容器內介質液位的實際高度，實現液位指示。
2、選擇時要考慮的因素
1測量對象，如被測介質的理化性質、工作壓力和溫度、安裝條件、液位變化速度等。
2測量和控制要求，如測量范圍、測量（或控制）精度、顯示方式、現場指示、遠程指示、與計算機的接口、安全和防腐、可靠性和施工方便性。
三。還應考慮磁性材料的退磁。消磁導致液位計不能正常工作，測量結果可能不準確。
3、不銹鋼磁性物位計的特性
1測量范圍大，不受容器高度的限制。
2適應癥新穎，閱讀直觀，醒目。指示器的方向可以根據用戶的需要改變。
三。適用于容器內液位和界面的測量。除現場指示外，還可配備遠程變送器、報警開關和完整的檢測功能。
4結構簡單，安裝方便，維護方便，耐腐蝕，無電源，防爆。
4、不銹鋼磁力液位計指示不準
&amp；1。判斷方法
�。�1）容器一直在運行，但容器的液位總是在某一點停止。
�。�2）當容器的負荷增加或減少時，容器的液位保持不變。
�。�3）就地液位計與室內顯示屏上的壓差液位計不匹配。
≫&gt；&gt；&gt；2。原因
�。�1）容器內的水上升或下降過快，也就是說浮子上升或下降過快，磁翻板沒有時間轉動。
�。�2）磁翻板的重心不在中心點。當磁懸浮列車上升時，它會隨著磁懸浮列車而翻轉。當磁懸浮列車再次升起時，翻板會回到原來的位置，并且沒有水位。
�。�3）集裝箱內的水中雜質過多，吸附在磁懸浮表面。其結果是，當磁懸浮上升時，它不能驅動翻板旋轉。
�。�4）水的液相管堵塞不同，使容器內實際水位上升。磁浮列車不會隨之上升。
≫&gt；&gt；&gt；3。解決方案
�。�1）盡量使容器內的水位上升或下降過快。
�。�2）水位計磁翻板，分
The stainless steel magnetic flap level gauge can be used to detect the medium liquid level of various tower,tank,tank,spherical vessel and boiler.Stainless steel magnetic flap level gauge can achieve high sealing,leakage proof and suitable for high temperature,high pressure,corrosion-resistant occasions.It makes up for the defects of glass plate(tube)liquid level gauge,such as poor clarity,easy to crack,and has no blind area in the whole process measurement,with clear display and wide measurement range.
Compared with other types of liquid level instruments,the safety of stainless steel magnetic flap level gauge has more advantages,because it is the local display of liquid level,which can be realized without relying on other electronic devices,and is stable and reliable with small fluctuation.Now it has been widely used in pressure vessels of thermal power plants:high and low pressure deaerator,raw water heater,heating network heater,high and low pressure of unit Heat exchangers such as heaters and condensers are equipped with such level meters.
The working medium of heat exchanger is easily vaporized liquid,the pressure is from vacuum state to 2.5MPa,and the temperature is from 40℃to 390℃.Therefore,the accuracy of daily maintenance and indication of level gauge plays an important role in the safe operation of pressure vessel.
This paper sorted out the stainless steel magnetic flap level meter related knowledge,let's have a look,hope to help you!
1、Working principle of stainless steel magnetic level gauge
The stainless steel magnetic flap level gauge(also known as magnetic float level gauge)works according to the principle of buoyancy and magnetic coupling.When the liquid level in the measured vessel rises or falls,the float in the main tube of the liquid level gauge also rises and falls.The permanent magnetic steel in the float is transmitted to the field indicator through magnetic coupling,which drives the red and white column to turn 180°when the liquid level rises,the turning column changes from white to red when the liquid level drops,and the red and white boundary of the indicator is the actual high of the medium liquid level in the container So as to realize the liquid level indication.
2、Factors to be considered in selection
1.The measurement object,such as the physical and chemical properties of the measured medium,as well as the working pressure and temperature,installation conditions,the speed of liquid level change,etc.
2.Measurement and control requirements,such as measurement range,measurement(or control)accuracy,display mode,on-site indication,remote indication,interface with computer,safety and corrosion protection,reliability and construction convenience.
3.The demagnetization of magnetic materials should also be considered.Demagnetization causes the level gauge not to work normally and the measurement results may be inaccurate.
3、Characteristics of stainless steel magnetic level gauge
1.The measurement range is large,not limited by the height of the container.
2.The indication is novel,the reading is intuitive and eye-catching.The direction of the indicator can be changed according to the user's needs.
3.Suitable for the measurement of liquid level and interface in the container.In addition to on-site indication,it can also be equipped with remote transmitter,alarm switch and complete detection function.
4.Simple structure,convenient installation,convenient maintenance,corrosion resistance,no power supply and explosion-proof.
4、Inaccurate indication of stainless steel magnetic level gauge
&1.Judgment method
(1)The container is always running,but the liquid level of the container always stops at a certain point.
(2)When the load of the container increases or decreases,the liquid level of the container remains unchanged.
(3)The local level gauge does not match the pressure difference level gauge on the indoor display screen.
≫>>>2.Reasons
(1)The water in the container rises or falls too fast,that is to say,the float rises or falls too fast,and the magnetic flap has no time to turn.
(2)The center of gravity of the magnetic flap is not at the central point.When the maglev rises,it will turn over with the maglev.When the maglev rises again,the flap will return to its original position,and there is no water level.
(3)There are too many impurities in the water in the container,which are adsorbed on the surface of maglev.As a result,the magnetic levitation decreases,and when the maglev rises,it can not drive the turnover plate to rotate.
(4)The blockage of the liquid phase pipe of water is different,which makes the actual water level in the container rise.Maglev does not rise with it.
≫>>>3.Solution
(1)Try to make the water level in the container rise or fall too fast.
(2)Magnetic flap of water level gauge,the center of gravity is not in the center point.If the manufacturing quality does not meet the standard,it should be replaced.
(3)If the water quality is unqualified,it should be washed regularly.
≫>>>4.Maintenance
(1)There should be no solid impurities and magnetic impurities in the cylinder of the liquid level meter,so as to avoid jamming the float and weakening the buoyancy.
(2)According to the medium condition,the main pipe can be cleaned regularly to remove the sediment impurities in the pipe.
(3)After cleaning the level gauge or changing the float,open the drain flange.When installing the magnetic float,pay attention to the heavy end with magnetic end upward,and do not install upside down.
(4)For low-temperature and special LPG products,the main body of the liquid level gauge is insulated by vacuum jacket.Pay attention not to damage the jacket during installation and use,so as to avoid affecting the product quality.
